ADT is known as one of the most popular security companies that offer alarm services to homeowners and businesses across the United States of America and Canada. ADT is among the top home security companies that offer a range of alarms to protect your home from burglars, fires, as well as other dangers. These systems are designed to dial the police or Fire Department when activated therefore it’s necessary to learn how to reset the ADT alarm system before fixing or making modifications. You risk setting it off should you disengage your system in the wrong manner since not all of them come with a silent disconnection feature.
I will explain the process and guide you on how you can disarm and disconnect your ADT alarm without triggering it. We will also quickly touch on introduction and reconnection to the service as well as troubleshooting in case of an issue. If you require to shut down your system, then, follow these directions, as instructed below.
Determine the position of the Main Alarm Panel The first action is finding the position of your primary ADT alarm panel since all the wirings converge to it. This is normally put in a closet, the basement utility room, or the garage for instance depending on the size of the house. It is a metallic container that looks like a book can weigh as much as a textbook and can have “ADT” printed on it or the top.
If you are not sure where your panel is or how it looks, then, make sure to look for the panel in any utility or storage room you can think of or call ADT to confirm the position. It is, therefore, important to locate this panel as it will enable them to disconnect everything safely.
Get the Passcode or Key After that, only the passcode or the physical key is required to open the panel box as shown below. The default ADT master codes could be as simple and easy to recall as 1-2-3-4, just like in the initial stages of using an ADT. However, for security purposes, the homeowners should change this main passcode later on to any other code that they alone know.
Enter Passcode Mode The next thing you should do is unlock the panel door and open it, and you should find a numeric touchpad inside akin to that of a telephone. Therefore, dial your master passcode slowly and accurately then press the pound key, to take the system to passcode programming mode.
An LED light will blink and in most cases, there shall be an announcement in a voice indicating that the system is ready for the next command. This tells you that you can now start feeding it more codes beginning with additional codes without activating the real alarm.
Initiate Disarm Sequence While the system is awaiting a response in passcode mode, enter your 4-digit master passcode again, and then, the “Off” key or number. This code sequence puts the system on full disarm mode where all the alarms are deactivated.
But you have to go to the next step, at least within a reasonable amount of time, because some keypads have an auto-rearm time of only 20-30 seconds for some of the zones. For exact details of your specific panel, it is always recommended to refer to your panel manual.
Cut Electric Power There should be an easily noticeable power switch or power cord within the metal box that you can easily locate. Switch off all electricity by pulling the switch to the OFF position or remove the transformer to disconnect the power supply. On the touchpad display, it should turn off meaning that the system has been safely disconnected from the power source.
For non-plugin types of systems, you might have to look for the circuit breaker or fuse that runs to the alarm wiring and turn that off. It is as simple as locating the panel wires to identify the correct circuit that has to be switched off.
Check for Backup Battery In addition, the majority of ADT panels are equipped with an emergency backup battery inside to ensure the system’s functioning during power outages. This battery comes in handy anytime the main power source is switched off, and the unit continues to run.
Therefore, be sure to remove that battery also before engaging in any further work. There may be a release tab for this keyboard to be removed easily. Switching off both types of power guarantees that the equipment is dead on, with no capability of powering any circuits.
Notify Monitoring Center Potential: Disconnection; When the ADT system is turned off, it cannot transmit information to ADT’s monitoring center. The last precautionary measure recommended is to call the ADT monitoring center and inform them that the system is being disconnected on purpose to be cleaned.
Give your name, address, and phone number, and state that you are an ADT customer with the customer I. D number. Simply say that the business is closing down temporarily due to renovations for home improvement. This avoids sending the police to respond to the scene at a later time by mistake.
Connecting Your ADT Home Security Alarm Your ADT alarm will be disconnected once your maintenance work is over and you will need to reconnect it again. First, if your unit comes with an internal backup battery, remove that as well. Switch on the master switch to turn on the main electrical supply and switch any circuit breakers that were previously turned off.
The green light beam should turn on Its steady state should be achieved The touchpad and the alarm panel should start to power up. Next, you should enter your master passcode, and press the pound key once more to activate the programming mode. Then type in the main access code followed by the letters ‘On’ to restore the full operation of the system.
It should all be online and back to talking to the ADT central station as we are now. Check this by opening some protected doors and also moving in front of some motion detectors to ensure the alarm system is working.
Troubleshooting Tips If your system won't reconnect or displays error messages after powering it back on, here are some troubleshooting tips:
-Ensure that all the wiring connections are correctly and tightly made. -Check that the electrical power is on and circuit breakers are set to ‘on’ -The first thing I need to check is to ensure that the backup battery has been properly mounted. -Try entering your codes again and slower -Consult with ADT service help if issues continue
By adhering to this guide, you will be able to manually disarm the ADT system to power it down and reconnect it for servicing or repair without triggering an alarm, or the siren, which would summon the authorities. But do remember to inform the center, switch off the power, and then proceed slowly. There is also the added difficulty of sorting through a large pile of such data, which will only be easy with time and practice. Stay safe!
Protect your home today with ADT’s top-rated security solutions!
Call now at +1 877-470-7879 to get a free consultation and find out how you can secure your home with the best in the business. Don’t wait—ensure your peace of mind with ADT!
