There may be instances when you will need to reset your ADT alarm system, whether for some reason you want to revert the settings to their factory state when the alarm system has been malfunctioning or if you are getting ready to transfer the alarm system to a new owner. Disarming an ADT alarm is typically a very simple process, and it differs slightly depending on the type of ADT panel that is installed in the house. 

Safewatch Pro 3000 is a type of alarm that is under the brand of ADT security company and in this article, we are going to explain how you can reset this kind of alarm. The Safewatch Pro 3000 is one of the key security systems offered by ADT and is widely used by homeowners. 

  1. Check that the system that is being alarmed is disarmed first. There will be digits on your keypad that read “000” whenever your system is disarmed.
  2. Pop the lid of the primary panel box where your ADT alarm is installed. This is a panel box, and it will require a security code to gain access.
  3. Find the reset/program button on the front panel of your ADT Safewatch Pro 3000 s. It should be labeled if your system has one, if at all.
  4. You have to hold this reset button until the system gives a beep and a voice command of “resetting all zones” which takes about 5-10 seconds.
  5. If you have heard two beeps, press the reset button. The system is now going to reboot to the factory settings as can be seen from the following screen. It brings out all your specific zone information, codes, and so on.
  6. After the reset is over, the keypad should read “000” and the system can be programmed and set to the desired configuration.

Guide On How To Rest ADT Command Smart Security Panel The Command series of security systems, are among the newest security systems that ADT has to offer. Here is how to reset a Command Smart Panel: 

  1. First of all, ensure your ADT Command is in a disarmed state.
  2. Locate where the main board, which is enclosed in the panel, is situated. This one requires you to have the master code before you can unlock it.
  3. To activate the panic button on your ADT Command Smart Panel, you need to press 1 and 3 together on the keypad simultaneously.
  4. Maintain the hold positions of 1 and 3 until the system gives two beeps and a verbal message of “restore. ” This shows that the reset process is underway.
  5. You will then hear the beeps and restore prompt, in the process you have to release buttons 1 and 3. Now, the panel will only finish the complete reset process all by itself. This erases all the information of a user, zone information among other things.
  6. When completed, the keypad will revert to the state of disarmed and show just 000 on the screen. You can then reprogram your system.
  7. What You Need To Know About ADT Pulse Control Panel Reset ADT Pulse is the latest smart home security technology by the company, offering users convenience, control, and even entertainment. Here is how to reset one: Here is how to reset one:
  8. If you can, sign in to Pulse through the web application or mobile application. If necessary, disengage from aggressiveness and be willing to disarm the system.
  9. Locate the main panel box that contains the control board and enter it by using the master PIN code.
  10. Switch off the main power supply and find the tamper switch before detaching it. It is a small part to fix the main panel enclosure to the PCB inside it to give strength to the whole unit.
  11. With the tamper switch turned off, set the pulse panel’s exit delay reset button then hold it down for 10-15 seconds.
  12. Keep an eye on the main panel LED lights. If it emits red orange and red repeatedly press the button. This confirms the reset.
  13. Follow up by power cycling the panel completely to complete the restore phase.
  14. Insert the tamper switch back if it was removed during a full power cycle of the alarm system.
  15. Go back and log into your Pulse account or Pulse mobile app and again set up /customize your system.
  16. ADT is a home security system that can be modified through its keypad; the following are the tips for resetting an ADT keypad instead. For some ADT panels like the Optex WF-20, you may be able to reset them by keypad instead of using internal buttons: For some ADT panels like the Optex WF-20, you may be able to reset them by keypad instead of using internal buttons:
  17. Double-check to ensure that the panel is disarmed and powered on.
  18. Press the ‘*’ button and the number ‘9’ to enter the master code, then press the ‘#’ button followed by ‘99’ to proceed to the programming mode.
  19. Use the arrow keys to go down to the 00 highlight and press enter when the 00 is highlighted.
  20. To get into the installation menu, type in the default code 4112 and press OK. This resets the panel.
  21. Exit programming mode. The steps, areas, numbers, etc will be recovered.
  22. As you can observe from the examples above, the process may differ in each system of ADT but these are the generalized steps to follow in the process. Once that is done make sure to power cycle if necessary and set your zones, user codes, etc again also be sure to inform ADT and any users of the system that a reset may have occurred. If you encounter issues with the ADT alarm panel reset, contact them for technical support.

  23. Protect your home today with ADT’s top-rated security solutions!

    Call now at +1 877-470-7879 to get a free consultation and find out how you can secure your home with the best in the business. Don’t wait—ensure your peace of mind with ADT!