ADT alarm systems are fitted withanan LCDy, which shows the current time when the system is armed or in operation. This clock is essential so that this programmed alarm runs as it is supposed to at the appropriate time. For instance, you could have your system programmed such that it turns into Armed–Away mode at some predetermined hour each night.

Maintaining time on an alarm panel is therefore essential for the proper functioning of the system. The procedure for altering the time is simple and can be completed within a short amount of time. But it does need the main alarm keypad as its control interface to work with other gadgets and peripherals. Given below are the instructions to alter the time for the ADT alarm system.

Prerequisites Before changing the time, ensure: Before changing the time, ensure:

  • On the alarm key,d you have a passcode to get to the Functions menu, and from there several options are available. This is usually the master password to the system.

  • The keypad is not currently armed or in an alarm condition or being used to run system tests.

    The initial step in the use of this software is to open the Functions Menu. The very first process is to get into the passcode by pressing the ‘#’ key and then pressing the Func key to get to the Functions menu. For example, if your passcode is 2580, you would enter: For example, if your passcode is 2580, you would enter:

    2580 Func

    The keypad display should include the functions menu. This is shown by writing “Func” in the upper right corner.

    Step 2 -Pressg the Enter Programming Mode Button In other words, starting from the Functions menu, you have to switch to the Programming mode. Press 8 and the two zeros.

    When executed properly, “Program” is indicated in the upper right sector of the display area. You’re now in programming mode where you can change things at the system level, such as the time.

    Step 3 – Click on the option that says ‘time’ which will take the user to the Time Submenu. Using the Next key and avoiding the Set key, scroll down to the word Time and stop there.

    Step 4 – This involves typing the 10-digit Time as shown in the figure below: With the time submenu displayed, enter the current time in 10-digit format: hh: mm x. x

    There are two figures to indicate the current hour in the 24-hour format and two figures for minutes and then AM/PM.

    For instance, to set the time to 9:30 AM you would enter: For instance, to set the time to 9:30 AM you would enter:

    0930 AM

    The panel clock to be updated as soon as you type in the tenth digit.

    Step 5 – Click on the save button then program exit Once this has been done press the Func button on the remote to save changes and exit the programming mode. The keypad switches back to the main Ready screen and, above the time, flashes and writes “Time Changed” for a moment.

    Confirm Proper Time Setting It is also advised to wait for at least 1 full minute after exiting the time programming modetoo see the panel clock incrementation that will indicate if the time was set successfully.

    If not, repeat the steps above to access the time submenu and re-enter the proper time in 10-digit HH:Proper MM XX format.

    Troubleshooting Help Normally, this is very easy when done asfollowd the procedures outlined above in changing the time. But if you have difficulty getting the process right, follow this additional advice: But if you have difficulty getting the process right, follow this additional advice:

  • Make sure that when you want to get into the Functions menu and then enter the master code, double and triple-check that you are entering the master code correctly to get into the Functions menu then press Func instantly.

  • The passcode should have full numeric permission to program the system. Some other passcodes like those designated for guestst, cleaners, or any other staff member may not have the adequate privilege.

  • When entering the time digits, go slowly and carefully to enter the proper HH: MM XX format – with AM or PM selected accordingly.

  • It may likewise freeze up if no keys are effective or if the display appears to be stuck. Reconnect it by finding the reset button which usually is around the transformer, then cycle the power on the unit.

    It is believed that, by strictly adhering to these guidelines while carefully verifying key entries, it is possible to make quick and easy changes to the time on the ADT alarm panel. However, if the problems persist, it is advisable to consult the ADT customer care services to get some solutions. Fortunately, their technicians can determine whether anything else such as low battery power is affecting normal functions as well as timekeeping.

  • Protect your home today with ADT’s top-rated security solutions!

    Call now at +1 877-470-7879 to get a free consultation and find out how you can secure your home with the best in the business. Don’t wait—ensure your peace of mind with ADT!