Disconnection of ADT Alarm Systems: An Overview The ADT is the most famous and reliable home security system that is widely used at present. Their systems are professionally installed and wired to allow you to monitor your home and dial for help in case of an emergency when the alarm is triggered. However, there are occasions when you may be required to switch off the ADT alarm temporarily for workers or guests to access your compound without triggering the alarm or in case of selling or renting the house and you are required to disarm the security system totally before the new tenant or owners move in. Regardless, there are indeed necessary measures to be taken to properly turn off an ADT alarm without causing an accidental alarm in the process of doing so.
In case one wishes to disconnect, one should always obtain authorization from the ADT first. The first thing you need to do is dial the toll-free number of your ADT monitoring center and inform them that you would like to disengage your system. They have to understand that you actively switch it off and when it is not on if it was disconnected or hacked which requires them to intervene. ADT may also have additional steps that they may want you to follow or they may want to make some checks on your system before they approve your system for disconnection so this first authorization call is therefore crucial.
Find Your Ctl Pnl and Decide on the Power Supply It is recommended that the ADT alarm control panels be fixed near the doors that lead to the exterior of the home or building but they can also be placed at any other location. If you cannot find the larger metal box with buttons, LCD, and possibly a phone jack connection, then follow any thick wires that come from the sensors on the doors and the windows or any other area and then use these wires to trace where they lead to and this will lead you to the main control box or panel. The panel will either be connected directly to the electrical supply system of your home meaning that it will always be powered or in some situations, you may have an ADT alarm panel that is powered only by battery or solar backup in cases where hard wiring was not possible at the time of installation. This must be established early as the ability to disconnect power is central to their complete neutralization.
Shut Off the Supplied Power to a Hardwired Alarm System If your ADT alarm system is connected to the home electrical system as the source of power, you should turn off the power by identifying the circuit breaker that powers the alarm panel. Most of the time it is doable for the ADT tech to inform you which one you have to turn off or sometimes there will be a labeled one just for the alarm system. Otherwise, you will have to switch off the breakers in succession and look for the one that controls the panel’s power. This power saving mode is accompanied by a ‘no power’ warning or complete blackout if on battery backup when the connected breaker is turned off and hence you get to cut power on the panel. Both indications ensure that you have successfully switched off the main power where you need it most.
Use the following tasks, Connection to phone and cell signal. Besides, AC power, home security systems require another line to connect to the ADT monitoring center for alarm events to be transmitted. This is most often either a phone cable or cellular antenna depending upon the age of the system you have. These cables should be connected to the control panel, so find them, and remove them. In older landline-connected systems the signal transmission can be easily halted just by pulling the telephone wire that connects to the wall jack. On cellular systems, the antenna wire will have a special clip-on connector that you can pinch and remove to allow the disconnection of the hardware from the panel.
Disable Backup Battery Almost all hard-wired ADT alarm control panels may come with a backup battery, which could be housed within the same unit as the control panel or be housed in a unit separate from the control panel. Cutting only AC power may not be enough to disable the system most of the time since this backup battery will still make the system try to activate alarms for some time even without the main power. Locate this battery and either unmount it from the panel or cut one of the wire leads to provide an open circuit and drain any residual backup charge from the system. This step only offers the final guarantee that any possibility for the system to receive power or send signals has been eliminated.
Welcome to World of Code Disability Enter Code to Disable System There should be no possibility of the ADT alarm activating at this point since they have no power, signal, or battery backup. However, it is recommended to turn off security monitoring officially using your system’s keypad to be more secure. Generally, all systems can be disarmed either with the help of your master code or by pulling down one of the programmed security buttons. You need to find out how to disable this mode by going through the paperwork you signed with ADT or your user manual given to you at the time of installation. The keypad on the system will display an affirmative notification that the monitor functions have been disabled once the right code is surrendered.
Restore Power When Ready After disarming the ADT alarm by following the above-mentioned prior steps that help in totally disconnecting the alarm from its power and communication, one would then proceed to the intended function like allowing workers to get in or preparing the house for demonstrating to potential buyers or in cases such as in selling a house and the like. Lastly, if you are ready to reinstate full security functionality, you just need to undo the steps beginning with rewiring the power at the circuit breaker that regulates the alarm system. It will then prompt for monitor to start and you can reconnect the backup battery and other cables. Still, give ADT a call again to make sure the system has resumed its normal state of functioning and is now armed so that they would know the system is now actively monitoring the home.
Extra Factors About Hardwired Smoke Alarms Another additional issue to consider is that while working on the ADT line, most wired smoke detectors connected to the alarm system will become inactive if the entire power is shut off. In these cases, it is useful to have battery backup smoke alarms that can be easily installed and used to test the main alarms. These can be wired and also mounted with battery power so they can be used while the wired units are disconnected for alarm system work. Just make sure to replace the hardwired detectors once done as they will often be hardwired together to all triggers to sound in the event of a smoke or fire detected anywhere in the home for the most advanced early warning system. The battery standalone units offer protection whilst actual alarm work is being carried out.
Conclusion
Even though ADT security systems can give your house optimum protection at all times, there are occasions when you would have to temporarily turn off the system. Minimizing contact with the alarm involves following the right procedures and in the right sequence to ensure the alarm is disconnected pending any work that may be conducted fully by changing power, transmission capability, and backup battery. Understanding how to turn off and reconnect these systems enables you to carry out repairs on the home without any interference with the alarm or monitor services. The only thing that you should ensure, is that you always get in touch with ADT before and after you disconnect your system to notify them of your new status in their computerized systems.
Protect your home today with ADT’s top-rated security solutions!
Call now at +1 877-470-7879 to get a free consultation and find out how you can secure your home with the best in the business. Don’t wait—ensure your peace of mind with ADT!
