If you have to restore your ADT Home Security System alarm to its initial state, the procedure is rather straightforward. Using factory reset is useful when you face technical problems, wish to clear all alarms, or set up the system for testing. From this guide, you shall be able to learn some of the steps that you are required to follow to complete the process of resetting your ADT alarm panel and ensuring that your system is ready to go again.

Guidelines to Follow Before Resetting Your ADT Alarm Before you reset your ADT alarm system, there are a couple of things you should do: 

Ensure Trouble Conditions –

This can be done on the ADT Pulse application or by calling the support team and checking if there are any trouble conditions on the system. Snoozing alarms or switching off the system when there is another condition negates the good results, instead causing more harm. Notify Your Monitoring Center – If you maintain professional monitoring for your system, it is essential to alert your monitoring center that you will be resetting your panel. This helps to prevent the alarm from being triggered by other devices. In practicality, it is quite easy to reset an ADT alarm system panel and the procedure will take only a few minutes. Nevertheless, to make sure that the reset was successful, one has to take a few minutes to check that all the buttons are in working order first.

Disabling a Hardwired ADT Home Security System Hardwired ADT security systems are by a panel that is hardwired into the electrical and permanent security sensors. 

1. Please key in your master code – Master codes can turn off and on the system as well as alarm it. Record yours on the alarm keypad. The default master code on the ADT terminals is either 1234 or 0000.

2. Turn off the system for a short time –

There is a button on the keypad, control panel, or alarm which is usually labeled Reset, Semi Reset, or Reset Sensor. To enter the desired temperature, press and hold down the button for 2-3 seconds.

3. Let the system reboot -

The keypad will have Reset in Progress written on it. Turn off the light and wait approximately seconds without touching any buttons on the remote control.

After the process of reset is complete on the system, the keypad will show a message as Ready to Arm. Your alarm system is now set to factory settings/restored to default values as directed.

How to Reset A Wireless ADT Security System ADT also provides wireless home security systems such as the ADT Pulse that utilizes specific controls for doors, windows, movements, window smashing, etc. 

1. Go to your ADT Pulse login – You may log in to the ADT Pulse account either through the website or by using your mobile device. Enter your login credentials.

2. Choose a Reset option – Depending on the page you are on, there should be a Reset System in the account menu. Select it.

3. Perform the final reset – This is the last step - your panel will lose wireless connection for some time. Check that they decide to continue.

4. Wait for about – Allow the system to take a certain time, which is about one and a half seconds in this case, to finish the resetting process.

After that, your panel will reconnect wirelessly to the sensors installed in your home and regain security.

Further advice relating to the process of resetting the ADT alarm is provided below. Here are some additional pointers to help make sure your ADT alarm reset goes smoothly: 

  • Ensure that there are no alerts of any trouble before the reset since this could interfere with the process.
  • If the firmware of the alarm is significantly outdated, then, download the new version for your alarm. This is refreshing as a way to start over.
  • After resetting, move around your home with your transmitters, and ensure various barriers and doors have been secured points.
  • If there is a failure in resetting any devices, then it is advisable to unpair and then repair the concerned devices to the wireless alarm panel.

DIY: For resets, when on the go then use the ADT Pulse mobile app while at home.

Thus, after choosing the correct reset actions for your particular alarm system model and making sure that everything is in order, you should be able to resolve the issue with your ADT equipment and ensure that it works as expected. Do not press buttons without purpose or intent, or you might reset components and unintentionally program them wrong. For any time issues, it offers an option to call the ADT support team that helps one solve different problems.

Summary Some of the basics that one has to undertake while resetting the ADT alarm include as follows: System Check: You should check for any problem facing your alarm system; Notification: In case the alarm is professionally installed, you should notify your monitoring center; Code Entry: You should enter your master code; Reset Button: You should then press the Reset button for several seconds; Completion Time: You should wait for some time before proceeding; Testing: At this Knowing these procedures make it easy to restore your ADT Security to normalcy in case there was a technical hitch that affected normal functioning or to prepare for demonstrations by setting all to their default state. That’s all about successfully resetting the trusty ADT alarm system that is used in homes and businesses today.

Protect your home today with ADT’s top-rated security solutions!

Call now at +1 877-470-7879 to get a free consultation and find out how you can secure your home with the best in the business. Don’t wait—ensure your peace of mind with ADT!